Trouble shooting of flywheel ring gear of gas generator set

　　瓦斯發電機組長時間運行難免會出現問題，今天小編為您介紹一下瓦斯發電機組飛輪齒圈故障及解決方案

　　There will inevitably be problems when gas generator runs for a long time. Today, I will introduce the flywheel gear ring fault of gas generator and Its Solutions

　　一、失敗原因

　　1、 Reason for failure

　　1. 瓦斯發電機組起動器與飛輪齒圈嚙合不良，有時會發生碰撞，造成齒輪損壞或單面磨損。如果齒面連續損壞或嚴重磨損超過三次，則啟動齒輪和齒圈很難嚙合。

　　1. The starter of gas generator set and flywheel ring gear are not meshed well, sometimes there will be collision, resulting in gear damage or single side wear. If the tooth surface is damaged continuously or severely worn more than three times, it is difficult for the starting gear and ring gear to mesh.

　　2、帶氣缸體的瓦斯發電機組。當發動機溫度過高時，發動機會熄火，發動機內部的熱量難以散發，活塞環與氣缸在高溫下粘連，氣體發生器冷卻后無法啟動。

　　2. Gas generator set with cylinder block. When the engine temperature is too high, the engine will shut down, the heat inside the engine is difficult to be dissipated, the piston ring and the cylinder are adhered under high temperature, and the gas generator cannot be started after cooling.

　　3、瓦斯發電機組曲軸抱枕。由于潤滑系統故障或機油不足而導致潤滑失敗，更終導致曲軸鎖定發動機而無法啟動。

　　3. Gas generator set crankshaft bolster. The failure of lubrication due to the failure of the lubrication system or the lack of oil eventually results in the engine being locked by the crankshaft and unable to start.

　　4、燃氣發生器噴射泵柱塞堵塞。

　　4. The plunger of injection pump of gas generator is blocked.

　　二、修復方法

　　2、 Repair method

　　1. 如果飛輪的齒輪環上有三顆以上的齒被損壞，如果這兩顆齒對著起動機，就不能嚙合。在這種情況下，您可以使用撬棒撬車輪環周圍的角度和重新啟動。損壞的飛輪齒一般可以焊接，嚴重的需要更換飛輪齒圈和起動機。

　　1. If more than three teeth on the flywheel gear ring are damaged, if the two teeth are facing the starter, they cannot be engaged. In this case, you can use a crowbar to pry the angle around the wheel rings and restart. The damaged flywheel gear can be welded generally, and the flywheel gear ring and starter need to be replaced seriously.

　　2. 若飛輪齒圈一側齒面磨損嚴重，可將齒圈壓下，前后端面翻轉后再裝上飛輪使用。

　　2. If the tooth surface of one side of the flywheel ring gear is seriously worn, the ring gear can be pressed down, the front and rear end faces can be turned over, and then the flywheel can be installed for use.

　　3、檢查齒輪嚙合是否正常后，啟動時飛輪不轉，應視為發動機內部故障，如曲軸抱死、活塞卡死氣缸、離合器卡死等，應進一步觀察。檢查離合器是否損壞，然后檢查注射泵柱塞是否卡住，發動機是否有異物等故障。

　　3. After checking whether the gear meshing is normal, if the flywheel does not rotate when starting, it shall be regarded as the internal fault of the engine, such as the crankshaft locking, the piston jamming the cylinder, the clutch jamming, etc., which shall be further observed. Check whether the clutch is damaged, then check whether the plunger of the injection pump is stuck, and whether the engine has foreign matters and other faults.

　　以上是瓦斯發電機組廠家為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.cxxrdz.com

　　The above is the related content introduced by the manufacturer of gas generator set. For more information, please visit the website: http://www.cxxrdz.com